Applicable Products
Overview
The reset button on your QNAP NAS allows you to perform two key actions: reset the administrator password and network settings, or restore the device to factory default settings. The required press-and-hold durations for each action depend on the hardware platform of your NAS (x86 for Intel/AMD-based models, ARM for ARM-based models).
Details
The following table summarizes the reset button behavior for different QNAP NAS hardware platforms:
Platform
(CPU Type) | Reset Password & Network Settings
(Press & Hold Duration) | Reset to Factory Default Settings
(Press & Hold Duration) |
|---|
| x86 (Intel/AMD) | 3 seconds | 15 seconds |
| ARM (e.g., TS-831X) | 3 seconds | 10 seconds |
Note:
- Pressing and holding the reset button for 3 seconds will reset the administrator password and network settings to default, but will not affect your data or other system settings.
- Pressing and holding the reset button for the longer duration (10 or 15 seconds, depending on platform) will restore the NAS to factory default settings. This action will erase all system settings and app configurations. User data and shared files will remain intact, but you will need to reconfigure your NAS after the reset.
Procedure
- Locate the reset button on the rear panel of your NAS. It is usually a small recessed button that requires a pointed object (such as a paperclip) to press.
- To reset the administrator password and network settings:
- Press and hold the reset button for 3 seconds until you hear one beep.
- To restore factory default settings:
- Press and hold the reset button for the platform-specific duration shown above (10 seconds for ARM, 15 seconds for x86) until you hear two beeps.
Warning: Restoring factory default settings will erase all system configurations and app settings. Your user data and shares will not be deleted, but you must reconfigure your NAS after the reset.
Further Reading
适用产品
概述
QNAP NAS 上的重置按钮允许您执行两个关键操作：重置管理员密码和网络设置，或将设备恢复到出厂默认设置。每个操作所需的按住时间取决于您的 NAS 硬件平台（x86 用于 Intel/AMD 型号，ARM 用于 ARM 型号）。
详情
下表总结了不同 QNAP NAS 硬件平台的重置按钮行为：
平台
（CPU 类型） | 重置密码和网络设置
（按住时间） | 恢复出厂默认设置
（按住时间） |
|---|
| x86（Intel/AMD） | 3 秒 | 15 秒 |
| ARM（例如，TS-831X） | 3 秒 | 10 秒 |
注意：
- 按住重置按钮 3 秒将重置管理员密码和网络设置为默认，但不会影响您的数据或其他系统设置。
- 按住重置按钮更长时间（10 或 15 秒，取决于平台）将恢复 NAS 到出厂默认设置。此操作将删除所有系统设置和应用配置。用户数据和共享文件将保持不变，但您需要在重置后重新配置您的 NAS。
步骤
- 在您的 NAS 后面板上找到重置按钮。它通常是一个需要尖锐物体（如回形针）按压的小型凹陷按钮。
- 要重置管理员密码和网络设置：
- 要恢复出厂默认设置：
- 按住重置按钮，按上述平台特定的时间（ARM 为 10 秒，x86 为 15 秒）直到您听到两声蜂鸣。
警告：恢复出厂默认设置将删除所有系统配置和应用设置。您的用户数据和共享不会被删除，但您必须在重置后重新配置您的 NAS。
进一步阅读
